You have 0 items in your cart.
Fluke
Sub Categories
3 Test Leads connected to Low-Leakage Probes (red, black, green) 3 Alligator Clips (red, black, green) Maximum Jaw Opening: 26 mm (1 in.) Replacement Test Lead Set for the Fluke 1550B MegOhmMeter Length (Lead Only): 2.6 m (8.6 feet) Cat II 1000 V, Cat III 600 V, 5kV DC Max (Probes) Cat II 1000 V, Cat III 600 V, 20 amps (Alligator Clips)
Patented TwistGuard extendable tip shroud that meets new electrical safety requirements to reduce tip exposure while providing the versatility needed for most measurements New WearGuard lead wire wear indicator. Each test lead is covered by two layers of silicone insulation; inner contrasting color is exposed when the leads are nicked, scuffed, or otherwise damaged and in need of replacement Double insulated silicone leads. TL175 withstands high temperatures and remains flexible in cold temperatures Extra-heavy strain relief on both probe-end and plug-end, tested beyond 30,000 bends without failure Universal input plugs compatible with all instruments that accept standard 4 mm shrouded banana plugs Probes always show correct category rating for tip exposure being used TL175E also available. Includes removable 4 mm lantern tips for versatility Conforms to EN61010-031 Ratings: CAT II 1000 V, CAT III 1000 V, CAT IV 600 V, 10 A max., Pollution Degree 2 Environmental ratings: -20 °C to 55 °C (-4 °F to 131 °F), altitude: 2000 m (6,562 ft) One-year warranty
Patented TwistGuard extendable tip shroud that meets new electrical safety requirements to reduce tip exposure while providing the versatility needed for most measurements New WearGuard lead wire wear indicator. Each test lead is covered by two layers of silicone insulation; inner contrasting color is exposed when the leads are nicked, scuffed, or otherwise damaged and in need of replacement Double insulated silicone leads. TL175 withstands high temperatures and remains flexible in cold temperatures Extra-heavy strain relief on both probe-end and plug-end, tested beyond 30,000 bends without failure Universal input plugs compatible with all instruments that accept standard 4 mm shrouded banana plugs Probes always show correct category rating for tip exposure being used TL175E also available. Includes removable 4 mm lantern tips for versatility Conforms to EN61010-031 Ratings: CAT II 1000 V, CAT III 1000 V, CAT IV 600 V, 10 A max., Pollution Degree 2 Environmental ratings: -20 °C to 55 °C (-4 °F to 131 °F), altitude: 2000 m (6,562 ft) One-year warranty
Replacement Test Lead Set For T5-600 and T5-1000 Electrical Testers
Length: 1.2m (48”) Bandwidth: 12,5 MHz Maximum Signal Voltage: 600V rms. CAT III per IEC 1010-2-031 Maximum Voltage to Ground: 600V rms. CAT III per IEC 1010-2-031 Maximum Current: 1A
Voltage Range: 0.25 to 30V rms Maximum Input Voltage: 30V rms, 200V dc AC to DC Ratio: 1:1 Ratio Accuracy (At 25 MHz and loaded with 10 M ohm) Above 0.5V: +/- 0.5 dB Below 0.5V: +/- 1.0 dB Add +/- 0.2 dB in RF fields of 1 to 3 V/m Frequency Response (Relative to 25 MHz): 100KHz to 100 MHz +/- 0.5 dB 100 MHz to 200 MHz +/- 2.0 dB 200 MHz to 500 MHz +/- 3.0 dB
Tone and trace wire on non-active networks SmartTone™ technology provides five distinct tones for exact pair identification Sends loud tone up to 10 miles (16 kilometers) on most cables Loud speaker on Probe makes the tone easier to hear through drywall, wood, and other enclosures Angled bed-of-nails clips allow easy access to individual pairs RJ11 connector is ideal for use on telephone jacks Attach nylon pouch (included in kit) to your belt for easy transport
Three tools in one: Fault locator Cable and wire manager Patented SmartTone analog tone generator Works on any two or more conductor cable up to 2,500 ft Instantly measures distance to open or any fault from one end of any cable pair Patented SmartTone tone generator positively identifies pair measures cable distance on spool Measures constantly while "on" Displays distance reading rather than waveform Moisture proof