You have 0 items in your cart.
Features : AC power supply(Power Supplies5.7”large LCD displayVarious output modes and measurement functionsAC-superimposed DC outputCapacitor input load supportedSequence functionLimiter function30 Sets of SAVE / RECALL memoriesUSB(USBTMC)standard for remote controlOutput On/Off FunctionAC power supply
Features : - 5.7" Large LCD Display- Output Capacity: 1kVA(for AC 200V Input)- Output Modes: AC and AC+DC Combined with any of four signal sources- Signal Source: Internal(INT),External(EXT),Internal+Externl(ADD)and Sychronization(SYNC)- Arbitrary Waveform Power Output- Power Amplifier of External Signal- Measurement Functions: Voltage, Current, Power ,Frequency, PowerFactor,CF,and Harmonic Current- Capacitor Input Load Supported- Sequence Function Allows Programming of Output Patterns- Limiter Function ( Upper / Lower / Limit Function)- 30 sets of Save / Recall Memory- Output On / Off Switch- USB(USBTMC)and RS-232 Standard for Remote Control- PC Software (Including Data Logging)
Features: -Sequence function to do high Efficient load simulations-Flexible configuration with mainframes and plug-in modules-Multiple independent load inputs up to 8 channels in a mainframe-Parallel connection of inputs for increased load capacity-Parallel connection of inputs for static and dynamic tests-Multiple channels run for dynamic tests under one clock control -Maximum rated power for low range high resolution CC tests-Von setting and Von on/off for start-up Von tests-Program mode to create work routines for repetitive tests-OPP/OCP/OVP/OTP protections-External channel control/monitoring via an analog control connector-Multi-Interface USB Device / Host, RS-232C, and GPIB (Optional) -Multi-mainframe link up to 5 mainframes in a system
Features : -Operating voltage (DC)：1.5V~150V-Operating Mode : C.C / C.V / C.R / C.P / CC+CV / CR+CV / CP+CV -Parallel Connection of Inputs for Higher Capacity (Max : 9,450W)-Support of High Slew Rate：Max 16A/us-Run Program Function（GO/NO GO Test）-Sequence Function for High Efficient Load Simulations-Commands are compatible with Kikusui PLZ-4W model.-Dynamic(Switching) Function：0.0166Hz ~20kHz-Soft Start Function：Off / On(1~200ms, Res：1ms)-Adjustable OCP / OVP / OPP / UVP Setting -Short Circuit Function-Timer function : Elapsed Time of load on -Cut Off Time(Auto Load Off Timer )：1s to 999h 59min 59s or Off -External Channel Control / Monitoring via Analog Control Connector-Setup Memories：100 sets-3.5 Inch TFT LCD Display-Multi Interface : USB 2.0 Device / Host , RS-232 , GPIB (Optional)
Features: 2/3/4 Independent Isolated Output4 LED Display Sets: 3 digits after decimal point Minimum Resolution : 1mV/1mA(GPD-2303D/GPD-3303S/GPD-4303S)100mV/10mA(GPD-3303D)Digital panel control(rotary encoder Switch, rubber key with indicator) User-friendly operation, coarse/fine volume control 4 Sets Save/Recall Key-Lock Output on/off Tracking Series and Parallel mode Smart cooling fan achieving low noise USB Standard InterfacePC Software & USB Driver Labview driver
Features: Single Output Dual Range Max. 200WHigh resolution: 1mV/1mA0.01% load/line regulation, 350uVrms rippleAuto step runing with timer setting and 100 Sets memorySafety design: OVP,OCP & OTP;Output ON/OFF controlSelf-test and software calibrationHighly visible vacuum-fluorescent displayFront and rear output terminalStandard interface : RS-232C, GPIBOption : European Jack Type Terminal
Features: Digitized Programmable Interface High Resolution 10mV, 1mA High Stability, Low Drift Over-Voltage, Over-Current, Over Temperature Protection Intelligent Fan Control (Changes by Output Power) Built-in Buzzer Alarm Labview Driver Standard Interface: RS-232C Optional Interface: GPIB (IEEE-488.2) Optional European Jack Type Terminal
Features:Digitized programmable interfacehigh resolution 10mV, 1mA 192 x 128 LCD display, simultaneously Over-voltage, over-current, over temperature protection Intelligent fan control (changes by output power) 100 Sets memory Auto step running with timer Provided auto series and parallel function Labview driver Standard interface: RS-232C Optional: GPIB (IEEE-488.2) Optional European jack type terminal